Volkswagen Polo Service & Repair Manual: Silicone Remover -LLS MAX 007

Volkswagen Polo Service & Repair Manual / General Paint Information / Original Products / SprayMax System / Silicone Remover -LLS MAX 007

Definition:

Silicone Remover -LLS MAX 007-

Edition 10/2008

Product Description

The Silicone Remover -LLS MAX 007- is a water-based, reduced-solvent cleaning agent that is rich in active ingredients. The raw material base has specific solvent combinations.

Properties:

Application-oriented product-specific aerosol formulation

Constant atomizing pressure

Aerosol distribution

Highest yield

Professional painting result

Highly effective cleaning- and degreasing agent

Strengthens the adhesion

Highest yield

Even distribution

Application Instructions

Application

Recommended for:

Parts painting and spot repair aid

Best suited for use during the subsequent painting of Aqua Plus water-based paints

Suitable base surfaces:

Primed, filled metal, plastic, glass, old- and factory paint surfaces, painted and unpainted base surfaces

Base Surface	Suitability
Primed, filled surfaces	+++
Factory and old paint	+++
Plastic parts	+++
Metal/glass	+++

Properties:

Painted surfaces do not become corroded

Removes all types of silicone, an ideal dirt and soot cleaner

Removes cavity sealant or wax

Removes gummy, dried-on grease residue, for example door hinges

Removes oil and grease residue

Ideal solvent for tar marks

Removes adhesive residue, for example stickers

Processing

Note

For work safety, wear appropriate, personal protective equipment:

Breathing mask type: A2/P2

Latex or nitrile protective gloves, for example

Application type “coat”

–	Apply a light coating immediately before applying the subsequent paint layer and right away wipe dry with a clean and dry cloth.

–	Do not allow the silicone remover to evaporate off the surface. Only work on small areas at the same time.

–	Repeat the cleaning procedure if the surface is very dirty.

–	Replace the cloths a few times. Do not use any dirty cloths.

Note

If the spray application is interrupted, make sure that the valve above the spray head is empty.

Caution

For work safety, wear appropriate, personal protective equipment.

Note the safety data sheets as well as the warnings on the label of the spray nozzle.

Dispose of the empty spray cans as recyclable material.

Characteristics

Silicone Remover -LLS MAX 007

Solid content:	0 %
Yield:	Approximately 0.75 to 1.0 m² / spray can
Gloss level:	not applicable
VOC value:	620 g/L, 248 g/can

Storage

The guaranteed shelf life of 36 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 °C (68 °F).

Silicone Remover -LLS MAX 007

Two-Part Wash Primer

Definition: Two-Part Wash Primer -LLS MAX 230 M1-, olive green (250 ml) Edition 12/2013 Product Descrip ...

Silicone Remover, Long -LLS MAX 008

Definition: Silicone Remover, Long -LLS MAX 008- Edition 10/2008 Product Description ...

Other materials:

Wire Break with Single Repair Point
Repair point with single crimp connection – Free up wire intended for repair (approximately 20 cm to both sides of repair point). – If required, remove wiring harness wrapping using a folding ...

Introduction
This chapter contains information on the following subjects: → Securing mounts, roof bars or load carrying system → Loading the load carrier system The roof of the vehicle has been designed for optimum aerodynamic effect. Therefore, conventional mounts or other load carrier sy ...

Locking or unlocking the driver door manually
Fig. 155 Door handle on driver door with lock cylinder First read and observe the introductory information and safety warnings If locked manually, all doors are locked. If unlocked manually, only the driver door is unlocked. Observe information on the anti-theft alarm . Fold the key bi ...