Volkswagen Polo Service & Repair Manual: Battery, Testing using Midtronics Battery Tester -MCR340VKT

Volkswagen Polo Service & Repair Manual / Battery, Starter, Generator, Cruise Control / Battery, Checking / Midtronics Battery Tester -MCR340VKT / Battery, Testing using Midtronics Battery Tester -MCR340VKT

Requirements

WARNING

Read and follow the Safety Precautions when working with batteries. Refer to → Chapter „Warnings and Safety Precautions“.

Batteries that have a light yellow visual indicator do not have to be tested or charged. Jump starting must not be used!

There is a risk of explosion during testing, charging or jump starting.

These batteries must be replaced.

–	Read the General Description. Refer to → Chapter „General Information“.

–	Visually check the battery. Refer to → Chapter „Visual Inspection“.

–	Open the hood or open the cover if the battery is installed somewhere else.

–	Determine if it is a “Standard” battery or an “AGM” battery.

–	Remove the covers on the battery positive and negative terminals.

–	Use a fender protector or some type of cover before using any equipment inside the engine compartment or inside the passenger compartment.

–	Close all the doors.

Note

The battery temperature must be at least 10 °C (50 °F).

Refer to the Battery Tester Charger Kit -VASRX3000- Operating Instructions for more information.

Performing the Test

WARNING

Batteries that have a light yellow visual indicator do not have to be tested or charged. Jump starting must not be used!

There is a risk of explosion during testing, charging or jump starting.

These batteries must be replaced.

–	Turn off the ignition and all electrical consumers.

–	Check the visual indicator. Refer to → Chapter „Battery with Visual Indicator, Checking“.

–	Switch on the unit.

–	Clamp the red clamp “+” of the tester to the positive terminal.

–	Clamp the black clamp “-” on the tester to the negative terminal.

Note

Make sure the test clamps make good contact!

–	Select “inside the vehicle” or “outside of the vehicle”.

–	Select “Warranty Test”.

Note

If the test results are needed to process a warranty claim, use the print function on the Midtronics Battery Tester -MCR340VKT-.

–	Determine if it is a “Standard” battery or an “AGM” battery.

–	Enter the battery DIN value taken from the battery label. If the label does not state a DIN value, then enter the SAE value.

–	Enter the DIN value into the tester and then perform the battery test. Refer to MCR340V Operating Instructions.

–	If using an SAE value, go into the menu under “other” and change “DIN” to “SAE”. Refer to MCR340VKT Operating Instructions.

Note

Always use the DIN value on the battery label. Otherwise the test result will be incorrect.

Evaluating Test Results

Battery Test Result

Battery Test Result	Measure
Battery good	None
Good - charge	Charge battery. Refer to → Chapter „Battery Tester Charger Kit -GRX3000VAS-“.
Use in charge	Charge battery. Refer to → Chapter „Battery Tester Charger Kit -GRX3000VAS-“.
Replace the battery.	Replace the battery. Refer to → Electrical Equipment; Rep. Gr.27
Battery cell defective	Replace the battery. Refer to → Electrical Equipment; Rep. Gr.27

General Information

WARNING Risk of injury. Read and follow the Safety Precautions when working with batterie ...

Midtronics Battery Tester -MCR340VKT-, Troubleshooting

Sometimes the display shows the malfunction or the messages based on the condition. The following is a list of the most frequent displayed mess ...

Other materials:

Introduction
This chapter contains information on the following subjects: → Wheel cover → Wheel bolt caps Additional information and warnings: Tyre monitoring system Cleaning and caring for the vehicle exterior Vehicle toolkit Changing a wheel Breakdown set ...

Cleaning and changing windscreen wiper blades
Fig. 142 Variants A and B: Changing the windscreen wiper blades. Variants B and C: Changing the rear window wiper blade First read and observe the introductory information and safety warningsThe factory-fitted windscreen/window wiper blades are coated with graphite. The graphite coating ens ...

Gear-change indicator
First read and observe the introductory information and safety warnings In some vehicles, the instrument cluster will show which gear should be selected while the vehicle is in motion to reduce fuel consumption. Display Meaning The c ...