Volkswagen Polo Service & Repair Manual: Wax Underbody Protection -D 316 000 A1
| Wax Underbody Protection -D 316 000 A1- |
| Wax Underbody Protection -D 316 000 A1- is an exceptional
long-term corrosion protection. |
| The Wax Underbody Protection is based on a solvent-free,
oxidative drying system and provides optimal corrosion
protection for the body underbody area. |
| This long-term corrosion protection is established by its
excellent adhesion at both very low and high temperatures to the
metallic surface. |
| The product forms a light brown, elastic and non-tacky
coating. |
| It is not necessary to combine the film at an elevated
temperature. |
| Wax Underbody Protection -D 316 000 A1- technical
application information |
| The material is primarily used in the vehicle area. |
| Make sure that the base surfaces are dry. |
| The ready-made product is applied using brushes at the
material temperature of +20 °C (68 °F) to 35 °C (95 °F). |
| The material can be carefully warmed up to 45 °C (113 °F)
immediately before applying (< 5 minutes) if it is required by
the application technique. |
| The oxidative hardening product can form a film on the
surface after a short time. This has no impact on the corrosion
protection or other properties. |
| 100% active ingredient content |
| Exceptional long-term corrosion protection |
| Low-temperature flexibility |
 Note
| Before starting to apply, it is necessary to read the safety
measures and advice in the safety data sheet. |
| Even for products which are not required to be labeled by
law, the usual safety measures must be observed for chemical
emissions. |
| The surfaces that are to be treated must dry and be free of
grease and dust. |
| Bring the Wax Underbody Protection to the application
temperature of 20° to 35 °C (68° to 95 °F). |
| Apply the material to the body parts that are to be
protected and spread using brushes. |
|
|
|
| Base |
Mixture of corrosion
protection additives with a sulfonate base, alkyd, mineral oil aromatic
extracts, pigments, thickening agents, drying agents and fluorescent
pigments. |
| Delivery form/color |
Light brown, viscous fluid |
| Rheomat viscosity |
1850 ± 350 mPas (System
PP50, d= 760 1/s |
| Density/15 °C DIN EN ISO
12185 |
0.995 ± 0.015 g/ml |
| Solid matter content |
99 ± 1 % |
| Flashpoint DIN EN ISO
2719 |
approximately 150 °C
(302°F) |
| Recommended layer
thickness |
100-400 µm |
| Processing temperature |
20° to 35 °C (68° to 95
°F) |
| Storage |
At temperatures of +10 °C
to +30 °C (50 °F to 86 °F) for approximately 12 months |
| Container |
310 ml |
Definition:
Wax Underbody Protection -D 316 D38 A2-
Edition 04/2009
Product Description
...
Definition:
Wax Spray -D 322 100 M2-
Edition 01/2011
Product Description
Wax Spr ...
Other materials:
Two-Part Filler
Definition:
Two-Part Filler -LLS MAX 202 M2-, medium gray
Edition 03/2013
Product Description
The Two-Part Filler -LLS MAX 202 M2-, (medium gray) is a
high-quality two-part H ...
Synchronising the vehicle key
First read and observe the introductory information
and safety warnings
It may no longer be possible to lock or unlock the vehicle with the remote control
if the button is pressed
repeatedly outside of the effective range of the vehicle key. If this is the case,
the vehicle key ...
Introduction
This chapter contains information on the following subjects:
→ Indicator lamp
→ Windscreen wiper lever
→ Windscreen wiper functions
→ Service position for the front windscreen wipers
→ Rain/light sensor
→ Checking and refilling the windscree ...
© 2016-2026 Copyright www.vwpolo.net
Wax Underbody Protection -D 316 D38 A2-
Wax Spray -D 322 100 M2