Volkswagen Polo Service & Repair Manual: One-Part Clear Coat

Volkswagen Polo Service & Repair Manual / General Paint Information / Original Products / SprayMax System / One-Part Clear Coat

Definition:

One-Part Clear Coat -LLS MAX 010-

Edition 10/2008

Product Description

The One-Part Clear Coat -LLS MAX 010- is a single-compound product. The raw material base is acrylic resin.

Properties:

Easy application (one-part material)

Dries quickly

High gloss

Universal usage

Easy polishing

Application Instructions

Application

Repair work and partial painting

Base Surface

Suitable base surfaces:

Solvent or water-based base paints

The base paint can be painted over with One-Part Clear Coat -LLS MAX 010- after 30 minutes.

Pre-treatment of base surfaces:

–	The base surface must be free of dust and grease.

One-Part Clear Coat

Processing

For work safety, wear appropriate, personal protective equipment.

Latex or nitrile protective gloves, for example

Breathing mask, for example type A2/P2

Application:

–	Thoroughly shake the can for at least two minutes and perform a short “spray test”.

One-Part Clear Coat

Application type “coat”

–	Apply two to three spray applications with a 5 to 10 minute intermediate ventilation time.

–	The recommended dry layer thickness is between 30 and 40 µm.

Spraying distance:

–	Maintain a distance of 20 to 25 cm.

Note

If the spraying procedure is interrupted, make sure that the valve above the spray head is empty to prevent any nozzle blockage.

One-Part Clear Coat

Drying

Air drying at +20 °C (68 °F) room temperature is:

Dust dry after 10 minutes

Firm coating after 20 minutes

Polishable after 12 hours

One-Part Clear Coat

IR drying is possible with this product. With short-wave heater, the IR drying is seven minutes.

Further Processing

–	The One-Part Clear Coat -LLS MAX 010- can be polished after 12 hours of air drying at +20 °C (68 °F) room temperature using a commercially available polish.

Caution

For work safety, wear appropriate, personal protective equipment.

Note the safety data sheets as well as the warnings on the label of the spray nozzle.

Shake briefly again before every subsequent spray application.

Dispose of the empty spray cans as recyclable material.

Characteristics

One-Part Clear Coat

Solid matter content	20% by weight
Yield	Approximately 0.5 m² to 075 m²/spray can with 30 - 40 μm dry layer thickness
Gloss level	90 units (60° measurement geometry)
Note	Used only by a professional
VOC value:	The EU limit for this product (product category IIB.b) in ready-to-use form is a maximum of 629 g/L volatile organic compounds. The VOC value of this product in ready-to-use form is a maximum of 252 g/can.

Storage

The guaranteed shelf life of 60 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 °C (68 °F).

One-Part Clear Coat

One-Part Test Paint

Definition: One-Part Test Paint -LLS MAX 005-, black Edition 10/2008 Product Description ...

One-Part Wash Primer

Definition: One-Part Wash Primer -LLS MAX 106 M2-, light gray One-Part Wash Primer -LLS MAX 107 M2-, dark gray ...

Other materials:

Stand -VAS6873/1
Definition: Stand -VAS6873/1- Product Description: Stand -VAS6873/1- with clock timer Technical Data: 220-240 V, 1 OH+PE Deliver ...

Controls for the air conditioning system
Fig. 125 In the centre console: air conditioning controls (manual) Fig. 126 In the centre console: Climatronic controls First read and observe the introductory information and safety warnings Press the corresponding button to switch a function on or off. When a function is switched on, ...

Cross-Section of a Radial Ply Tire
1 - Tread Block 2 - Tread Groove 3 - Tread 4 - Nylon Ply 5 - Belt Layers Consists mostly of steel 6 - Bead Bundle ...