Volkswagen Polo Service & Repair Manual: Blender
| Blender was developed for hassle-free two-part clear coat
and top coat touch-up. |
| Applies well to all base surfaces |
| Blends well with the old paint |
| Keep the filler surface as small as possible. |
| Paint filler spot thoroughly with water-based base paint
(overlapping spray applications) |
|
|
|
| Touch-Up System for Two-Part Clear Lacquers |
| Mixing ratio for two-part clear coat: |
| Adjust the two-part clear coat according to technical
application information. Refer to
→ Chapter „Clear Coats“. |
|
|
|
| – |
Paint over the water-based base paint with adjusted clear
coat (overlapping spray applications). |
|
|
|
| – |
Apply pure Blender -LVE 013 100 A2- onto the touch-up area
inside the sanded surface. |
|
|
|
| Touch-Up System for Two-Part Top Coats |
| Mixing ratio for two-part top coat: |
| Adjust the two-part top coat according to technical
application information. Refer to
→ Chapter „Top Coats“. |
|
|
|
| – |
Paint over filler area thoroughly (overlapping spray
applications). |
|
|
|
| – |
Apply pure Blender -LVE 013 100 A2- onto the touch-up area
inside the sanded surface. |
|
|
|
| Polishing the Touch-Up Zones |
| Air dry at +20 °C (68 °F) room temperature: |
| Polish the touch-up areas after they have dried overnight |
|
|
|
| Final drying time with forced drying is a minimum of 5 to 10
minutes. |
|
|
|
| Forced drying is at +60 °C (140 °F) object temperature for
30 minutes. |
| – |
After that, allow the touch-up areas to cool off for an hour
and polish at +20 °C (68 °F) room temperature. |
|
|
|
| Final drying time for IR drying is a minimum of 5 to 10
minutes. |
|
|
|
| IR dry with a short-wave radiator for 10 minutes |
| – |
After that, allow the touch-up areas to cool off for an hour
and polish at +20 °C (68 °F) room temperature. |
 Note
| Polish the touch-up area with fine polishing paste by hand
or with a polishing machine. |
| To finish, treat the surface with high-gloss sealant. |
|
|
|
| Personal Protective Equipment: |
| Note the safety data sheets |
| Wear the personal protective equipment during application |
|
|
|
| Flashpoint: |
+20 °C (68 °F) |
| The guaranteed shelf life of 60 months from date of
manufacture. Use no later than the date indicated on the label
and store in original container at +20 °C (68 °F). |
|
|
|
Definition:
Two-Part HS Performance Clear Coat -LZK 769 K06 A5-
Edition 08/2012
Product Description
...
Other materials:
Warning and indicator lamps
First read and observe the introductory information
and safety warnings
Lit up
Possible cause
Solution
Handbrake is applied.
Release the handbrake .
Brake system fault.
Do not drive on!
Obtain profe ...
Antenna Wires, Replacing
A new repair concept has been developed for repairing
antenna wires. Refer to
→ Chapter „Antenna Wires, Repairing“.
Instead of a complete antenna wire, connecting wires of
different lengths and various adapter leads are no ...
Wiring Harness Repair Set - Wire Strippers -VAS1978/3
The Wiring Harness Repair Set - Wire Strippers -VAS1978/3-
is used for professional stripping and cutting of wires.
The Wiring Harness Repair Set - Wire Strippers -VAS1978/3-
is a component of the Wiring Harness Repair Set -VAS1978B- and
...
© 2016-2026 Copyright www.vwpolo.net
Two-Part HS Performance Clear Coat
Hardener