Volkswagen Polo Service & Repair Manual: Wax Underbody Protection -D 316 000 A1

Volkswagen Polo Service & Repair Manual / General Paint Information / Original Products / Wax Underbody Protection / Wax Underbody Protection -D 316 000 A1

Definition:

Wax Underbody Protection -D 316 000 A1-

Edition 01/2008

Product Description

Wax Underbody Protection -D 316 000 A1- is an exceptional long-term corrosion protection.

The Wax Underbody Protection is based on a solvent-free, oxidative drying system and provides optimal corrosion protection for the body underbody area.

This long-term corrosion protection is established by its excellent adhesion at both very low and high temperatures to the metallic surface.

The product forms a light brown, elastic and non-tacky coating.

It is not necessary to combine the film at an elevated temperature.

Wax Underbody Protection -D 316 000 A1- technical application information

Application

The material is primarily used in the vehicle area.

Make sure that the base surfaces are dry.

The ready-made product is applied using brushes at the material temperature of +20 °C (68 °F) to 35 °C (95 °F).

The material can be carefully warmed up to 45 °C (113 °F) immediately before applying (< 5 minutes) if it is required by the application technique.

The oxidative hardening product can form a film on the surface after a short time. This has no impact on the corrosion protection or other properties.

Properties

Solvent-free

100% active ingredient content

Exceptional long-term corrosion protection

Good adhesion properties

Reduced tendency to drip

Low-temperature flexibility

Long shelf life

Note

Before starting to apply, it is necessary to read the safety measures and advice in the safety data sheet.

Even for products which are not required to be labeled by law, the usual safety measures must be observed for chemical emissions.

Processing

The surfaces that are to be treated must dry and be free of grease and dust.

Bring the Wax Underbody Protection to the application temperature of 20° to 35 °C (68° to 95 °F).

Apply the material to the body parts that are to be protected and spread using brushes.

Technical Data

Base	Mixture of corrosion protection additives with a sulfonate base, alkyd, mineral oil aromatic extracts, pigments, thickening agents, drying agents and fluorescent pigments.
Delivery form/color	Light brown, viscous fluid
Rheomat viscosity	1850 ± 350 mPas (System PP50, d= 760 1/s
Density/15 °C DIN EN ISO 12185	0.995 ± 0.015 g/ml
Solid matter content	99 ± 1 %
Flashpoint DIN EN ISO 2719	approximately 150 °C (302°F)
Recommended layer thickness	100-400 µm
Processing temperature	20° to 35 °C (68° to 95 °F)
Storage	At temperatures of +10 °C to +30 °C (50 °F to 86 °F) for approximately 12 months
Container	310 ml

Wax Underbody Protection -D 316 D38 A2-

Definition: Wax Underbody Protection -D 316 D38 A2- Edition 04/2009 Product Description ...

Wax Spray -D 322 100 M2

Definition: Wax Spray -D 322 100 M2- Edition 01/2011 Product Description Wax Spr ...

Other materials:

Physical Principles
The four known states of water also apply to air conditioning system refrigerants. 1 - gaseous (invisible) 2 - vapor 3 - fluid 4&nbs ...

Service Charging with Battery Charger -VAS5900
Special tools and workshop equipment required Battery Charger -VAS5900- WARNING Risk of injury. Follow all Warnings and Safety Precautions. Refer to → ...

Maximum permitted trailer weights
First read and observe the introductory information and safety warnings All data in the official vehicle documents take precedence over these data. All data in this manual apply to the basic model. The vehicle data sticker in the service schedule and the official vehicle documents show which ...