Volkswagen Polo Service & Repair Manual: Two-Part HS Optimum Plus Clear Coat

Volkswagen Polo Service & Repair Manual / General Paint Information / Original Products / Clear Coats / Two-Part HS Optimum Plus Clear Coat

Definition:

Two-Part HS Optimum Plus Clear Coat -LZK 769 K07 A5-

Edition 04/2013

Product Description

The two-part HS optimum plus clear coat is a VOC compliant high solid clear coat. Optimal application even under unfavorable booth conditions, for example low drying temperature.

Properties:

Flexible and efficient application possible

Dries very quickly

Quick and easy to polish

It is possible to use HS Spot Thinner -LVM 006 000 A2-

Application Instructions

Base Surface

Suitable preliminary coatings:

Water-based base paints

Processing

Mixture ratio:

–	3:1 by volume with:

Two-Part VHS Hardener -LHA 009 051 A2-/-LVM 009 051 A5-

Two-Part VHS Hardener, Short -LHA 009 050 A2-

Two-Part VHS Hardener, Long -LHA 009 052 A2-/-LHA 009 052 A3-

Two-Part VHS Hardener, Extra Long -LHA 009 053 A2-

See technical application information for the two-part VHS hardener. Refer to → Chapter „Two-Part VHS Hardener and Two-Part VHS Performance Hardener“.

Thinner:

Two-Part Thinner, Special -LVM 009 200 A2-/-LVM 009 200 A5-

Two-Part Thinner, Long -LVM 009 300 A2-

HS Spot Thinner -LVM 006 000 A2-

See the technical application information on the LVM 006 000 A2 HS spot thinner. Refer to → Chapter „HS Spot Thinner“.

For elastification. Refer to → Anchor.

Two-Part HS Optimum Plus Clear Coat

Processing time/pot life:

–	Ready to spray in 45 to 60 minutes at +20 °C (68 °F) (depending on the hardener used)

Two-Part HS Optimum Plus Clear Coat

Application type “coat”

Two-Part HS Optimum Plus Clear Coat

–	Processing viscosity at +20 °C (68 °F) material temperature is the mixing viscosity for “Compliant” and “HVLP”.

Two-Part HS Optimum Plus Clear Coat

–	Set spray nozzle (see manufacturer's information): “Compliant” 1.2 to 1.3 mm.

–	Set spray nozzle (see manufacturer's information): “HVLP” 1.3 to 1.4 mm.

–	Set spray pressure (see manufacturer's information): “Compliant” to 2.0 to 2.5 bar.

–	Set atomizing pressure (see manufacturer's information): “HVLP” 0.7 bar.

Two-Part HS Optimum Plus Clear Coat

–	Apply 1.5 coats.

Note

During the spray application process, the first half spray application should form a thin, nearly complete film upon which a fully-completed spray application can be applied.

–	The recommended dry layer thickness is between 40 and 60 µm.

Note

When using as a clear coat for minimal damage repairs (clever repair procedure), 10 % Two-Part Thinner, Special -LVM 0009 200 A2- and Two-Part Thinner, Special -LVM 009 200 A5- can be replaced with 10 % HS Spot Thinner -LVM 006 000 A2 HS-. Do not apply on slanted surfaces.

Two-Part HS Optimum Plus Clear Coat

Drying

Air dry at +20 °C (68 °F) room temperature:

Dust dry after 15 to 30 minutes

Ready for assembly after 2 to 5 hours

Dry overnight

Two-Part HS Optimum Plus Clear Coat

Final drying time with forced drying is 5 minutes.

Two-Part HS Optimum Plus Clear Coat

Forced drying at +60 °C (140 °F) object temperature with:

Two-Part VHS Hardener -LHA 009 051 A2-/-LVM 009 051 A5- for 15 to 25 minutes.

Two-Part VHS Hardener, Short -LHA 009 050 A2- for 10 to 15 minutes.

Two-Part VHS Hardener, Long -LHA 009 052 A2-/-LHA 009 052 A3- for 20 to 30 minutes.

Two-Part VHS Hardener, Extra Long -LHA 009 053 A2- for 25 to 35 minutes.

Two-Part HS Optimum Plus Clear Coat

Final drying time for IR drying is 5 minutes.

Two-Part HS Optimum Plus Clear Coat

IR dry with short-wave heater for 8 to 12 minutes

Two-Part HS Optimum Plus Clear Coat

Special Instructions

Elastification for rigid and semi-rigid plastics:

The base material must first be mixed with 15 % Elastic Additive -ALZ 011 001-.

Mixture with two-part VHS hardeners, 3:1 with 10 % Two-Part Thinner, Special -LVM 009 200 A2- or Two-Part Thinner, Special -LVM 009 200 A5- (drying period is lengthened).

Two-Part HS Optimum Plus Clear Coat

Personal Protective Equipment:

Note the safety data sheets

Wear the personal protective equipment during application

Characteristics

Two-Part HS Optimum Plus Clear Coat

Flashpoint:	above +23 °C (73.4 °F)
VOC value: 2004/42/IIB(d)(420)420	The EU limit for this product (product category IIB.b) in ready-to-use form is a maximum of 420 g/L volatile organic compounds. The VOC-value of this product in ready-to-use form is a maximum of 420 g/L.

Storage

The guaranteed shelf life of Two-Part HS Optimum Plus Clear Coat -LZK 769 K07 A5- is 48 months from date of manufacture. Use no later than the date indicated on the label and store in original container at +20 °C (68 °F).

Two-Part HS Optimum Plus Clear Coat

Two-Part HS Optimum Clear Coat

Definition: Two-Part HS Optimum Clear Coat -LZK 769 K02 A5- Edition 10/2012 Product Description ...

Two-Part Brilliant Clear Coat

Definition: Two-Part Brilliant Clear Coat -L2K 769 K04 A5- Edition 10/2010 Product Description ...

Other materials:

Handling Pressure Vessels
Secure vessels to prevent them falling over! Secure upright cylinders to stop them falling over and cylinders lying flat to stop them rolling away. Do not throw vessels! If dropped, the vessels cou ...

Vehicle Registration Documents Since 01/10/2005
The implementation of EU guideline 1999/37/EG "Vehicle registration documents" in national legislation and legal data protection requirements have made the introduction of new, fraud resistant registration documents necessary. ...

Manual gearbox: selecting a gear
Fig. 110 Gear shift pattern of a 5 or 6-speed manual gearbox First read and observe the introductory information and safety warnings The positions of the individual driving gears are shown on the gearshift lever . Fully depress and hold the clutch pedal. Move the gear lever t ...