Volkswagen Polo Service & Repair Manual: Two-Part Fine Filling Paste
| Two-Part Fine Filling Paste -LSP 784 002 A2- |
| The two-part fine filling paste is a very fine thixotropic
polyester filling paste. |
| This filling paste is suitable for small repairs. |
| High elasticity for touching up synthetic surfaces |
| Glass fiber reinforced plastics |
| Old paint and factory paint |
| Hardened two-part filler/two-part primers |
| Plastic parts glaze-primed with Two-Part Plastic Adhesive
Filler -LKF 696 009 A2-/-LKF 696 040 A2- or Adhesion Promoter -ALO
822 000 10- |
| Primed surfaces with two-part polyester filling paste. |
Caution
| This filling paste may not be applied to PVB
(acid-hardening) adhesive primers or one-part primers
(for example, synthetic resin). |
| Application on thermoplastic or elastic coatings is
also not possible. In these cases, only apply filler
paste to bare steel. |
|
|
|
|
| Pre-treatment of base surfaces: |
| – |
Remove any grease and sand the surface. |
| – |
Bare metallic base surfaces are to be insulated with
Two-Part Wash Primer -LHV 043 000 A2- and then filled with
Two-Part HS Performance Filler. Sand the filler after drying. |
| – |
With UP-GF underbodies, clean components of any residual
agents and sand the surface. |
|
|
|
| – |
Use a suitable cleaning agent before reworking to ensure a
clean and residue-free surface. |
|
|
|
| – |
Add 2 to 3 % by weight Two-Part Hardener -LVM 018 000 A1/A2-
or, especially when dealing with high temperatures, Two-Part
Hardener, Long -LVM 018 100 A2-. |
 Note
| Avoid using excessive hardener paste, to prevent it from
bleeding through, especially on daylight colors and light
metallic colors. |
| – |
At +20 °C (68 °F) room temperature for about three to five
minutes. |
|
|
|
| – |
At +20 °C (68 °F) room temperature for about 20 to 30
minutes. |
|
|
|
| Short-wave heaters for three minutes (at 50 % power) |
| Medium-wave heaters for five minutes. |
|
|
|
| In connection with the aforementioned drying time: |
| – |
Dry-sand the pre-sanding with P180-240 grit sandpaper |
| – |
Dry-sand the final sanding with P240-320 grit sandpaper |
|
|
|
| – |
While wet, sand the pre-sanding with P240-320 sandpaper |
| – |
While wet, sand the final sanding with P600-800 sandpaper |
Note
| When wet-sanding, make sure to wipe and dry off the surface. |
| Temperature resistance up to +80 °C (176 °F). |
|
|
|
| One-Part Wash Primer -LVM 044 007 A2-/-LVM 044 171 A2- |
| Two-Part Wash Primer -LHV 043 000 A2- and Two-Part HS Vario
Filler |
| Two-Part Plastic Adhesive Filler -LKF 696 009 A2-/-LKF 696
040 A2- |
| Unelasticized Adhesion Promoter -ALO 822 000 10- and
Two-Part HS Filler (for plastic parts) |
| – |
Then paint over with the top coat. |
|
|
|
| Personal Protective Equipment: |
| Note the safety data sheets |
| Wear the personal protective equipment during application |
|
|
|
| Delivery Viscosity |
pasty |
| Flashpoint: |
Filling paste over 23 °C (73.4
°F) |
| VOC value: 2004/42/IIB(b)(250)170 |
The EU limit for this product
(product category IIB.b) in ready-to-use form is a maximum of 250 g/L
volatile organic compounds. The VOC-value of this product in
ready-to-use form is a maximum of 170 g/L. |
| The guaranteed shelf life is 12 months from the production
date. Use no later than the date indicated on the label and
store in original container at +20 °C (68 °F). |
|
|
|
| – |
Storage Temperature +20 °C (68 °F) (temperature should not
exceed +30 °C (86 °F)). |
|
|
|
Definition:
Two-Part Steel Filling Paste Set -DA 787 300 A2-
Edition 09/2012
Product Description
...
Definition:
Two-Part Fine Filling Paste, Flexible -LSP 787 100 A1-
Edition 07/2010
Product Description
The T ...
Other materials:
Charging Systems not Requiring a Permit
At this time, A/C service units for extracting, cleaning and
filling refrigerant for motor vehicle A/C systems are available
from various manufacturers.
Charging systems not requiring a permit are ones used for
transferring compressed ga ...
Cavity Sealant
Definition:
Cavity Sealant -D 330 KD1 A2-
Cavity Sealant -D 330 KD2 A1-
Edition 04/2010
Product Description
Cavity Sealant -D 330 KD1 A2- and Cavity Se ...
Tire Pressure Monitoring Sensor with Valve, Removing and Installing
Removing
–
Remove the union nut -1-.
–
Remove Tire Pressure Monitoring Sensor-2-
from rim well.
Installing
...
© 2016-2026 Copyright www.vwpolo.net
Two-Part Steel Filling Paste Set
Two-Part Fine Filling Paste, Flexible