Volkswagen Polo Service & Repair Manual: Stone Chip Protection -AKR 311 KD1 05
| Stone Chip Protection -AKR 311 KD1 05-, black |
| Stone Chip Protection -AKR 311 KD1 05- is a finely atomizing
coating material with a synthetic resin basis. |
| The dried film adheres very well to cleaned base surfaces as
well as to an bare and painted panel. |
| It is characterized by a high covering capacity, good
protection against corrosion, high resistance to abrasion and
therefore good protection against stone impacts. |
| After approximately seven minutes the quick-drying stone
chip protection spray can be painted over using commercially
available vehicle paint systems. |
| Oven drying at approximately 60 °C (140 °F) is possible
without any problems. |
| Extraordinary mechanical stress (for example, automatic car
washes) should be avoided in the first few weeks. |
| The mechanical load-bearing capacity of the painted surfaces
can be found in the manufacturer's product specifications. |
| Stone Chip Protection -AKR 311 KD1 05- is used on visible
components, such as front and rear aprons and door sills to
protect against stone impact, grit, and moisture corrosion. It
can be quickly painted over. |
| The material is also used to supplement stone chip
protection linings, for work on particular points of a vehicle
and during accident repair work. |
 Note
| Before starting to apply, it is necessary to read the safety
measures and advice in the safety data sheet. |
| Even for products which are not required to be labeled by
law, the usual safety measures must be observed for chemical
emissions. |
| Clean the surfaces to be treated with Stone Chip Protection
well beforehand and remove any rust. |
| The surfaces must be dry, free of grease, dirt and as much
dust as possible. |
| The material should be at room temperature during
application. |
| Shake the can thoroughly; when the ball bearings start to
rattle, continue shaking for approximately one minute. |
| Hold the can vertically when spraying and spray from a
distance of 20 to 30 cm. |
| If parts of the vehicle were covered before spraying, the
covers should be removed before drying. |
| Abrasion and corrosion protection increases with the layer
thickness. For this reason one or two additional coats should be
applied after a short ventilation time. |
| To prevent spraying shadows the material is sprayed on in
cross patterns. |
| After use, the can and the valve should be held down and the
valve sprayed until only propellant gas emerges. |
Caution
| Do not spray onto moving or high-temperature
components such as the steering, engine, transmission,
driveshaft, exhaust, catalytic converter and brake
system. |
|
| Splashes and paint mist can be removed immediately with
gasoline. |
| Dried material can only be removed with D or R thinner. Be
careful with fresh paint! |
|
|
|
| Color |
Bright/black |
| Odor |
Solvent |
| Thickness after 2 to 3
cross spray applications |
250-300 µm dry film |
| Drying time |
Dust dry after
approximately two hours |
| Processing temperature |
+15 °C to +25 °C (59° to
77 °F) |
| Application temperature |
-29 °C to +70 °C (84.2° to 158
°F) (short-term, up to one hour at +100 °C (212 °F)) |
Definition:
Stone Chip Protection -AKR 311 KD1 10-, black
Edition 02/2014
Product Description
...
Other materials:
Synchronising the vehicle key
First read and observe the introductory information
and safety warnings
It may no longer be possible to lock or unlock the vehicle with the remote control
if the button is pressed
repeatedly outside of the effective range of the vehicle key. If this is the case,
the vehicle key ...
Refrigerant Circuit Pressures and Temperatures
WARNING
When performing work on refrigerant circuit, observe
all generally applicable safety precautions and pressure
vessel regulations.
The pressures and temperatures in ...
Warranty Test, Performing
WARNING
Do not check or charge batteries that have a visual
indicator that is bright yellow. Jump starting must not
be used!
There is a risk of explosion during testing,
cha ...
© 2016-2024 Copyright www.vwpolo.net
Stone Chip Protection -AKR 311 KD1 10