Volkswagen Polo Service & Repair Manual: Plastic Primer
Adhesion Promoter (Glazing)
| Adhesion Promoter -ALO 822 000 10- (glazing) |
| The glazing adhesion promoter is a universal
single-component adhesion promoter for all standard exterior
plastic car parts. |
| This adhesion promoter is characterized by its reliable
adhesion, high elasticity and the ease with which it can be
used. |
| All standard plastic parts used on car exteriors. |
| PP, EPDM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC |
|
|
|
| Pre-treatment of base surfaces: |
| The base surface must be free of separating agents. |
| Before cleaning plastic parts, temper them for 60 minutes at
+60 ℃ to “sweat out” the separating agents. |
| – |
Clean using Antistatic Plastic Cleaner -LVM 001 001 A2- or a
milder Silicone Remover, Long -LVM 020 100 A5-. |
 Note
| The effort needed for cleaning depends on the type and
quantity of the separating agent used. We recommend using a
sanding pad to help cleaning |
| Let the thinner evaporate (for example, air-drying overnight
at room temperature or 30-40 minutes at +60 ℃). |
|
|
|
| – |
Before priming, lightly clean again using Antistatic Plastic
Cleaner -LVM 001 001 A2- or Silicone Remover, Long -LVM 020 100
A5- (antistatic effect). |
|
|
|
| – |
Do not add any thinner! |
|
|
|
| – |
Processing viscosity 4 mm for +20 °C (68 °F), German
Industry Standardization 53211 |
Note
| Do not add any thinner! The delivery viscosity is the same
as the processing viscosity. |
| Processing viscosity 4 mm gravity feed spraygun “Compliant”
and “HVLP”: |
|
|
|
| – |
Set spray nozzle (see manufacturer's information):
“Compliant” 1.2 to 1.4 mm. |
| – |
Set spray nozzle (see manufacturer's information): “HVLP”
1.3 to 1.5 mm. |
| – |
Set spray pressure (see manufacturer's information):
“Compliant” to 2.0 to 2.5 bar. |
| – |
Set atomizing pressure (see manufacturer's information):
“HVLP” 0.7 bar. |
|
|
|
| – |
A preliminary spray application is 1 to 2 µm. |
|
|
|
| Air dry at +20 °C (68 °F) room temperature, can be sprayed
over after 15 minutes. |
|
|
|
| Can be sprayed over with two-part HS filler elasticized with
Elastic Additive -ALZ 011 001- after drying time at +20 °C (68
°F). |
| Afterwards, can be painted over with: |
| Water-based base paint and two-part HS clear coat |
|
|
|
| Personal Protective Equipment: |
| Note the safety data sheets |
| Wear the personal protective equipment during application |
|
|
|
| Delivery Viscosity |
11 seconds |
| Flashpoint: |
above +23 °C (73.4 °F) |
| The guaranteed shelf life is 24 months from production date.
Use no later than the date indicated on the label and store in
original container at +20 °C (68 °F). |
|
|
|
| The prescribed storage temperature is +20 °C (68 °F) (not to
fall below +5 °C (41 °F)). |
|
|
|
Definition:
Two-Part Wash Primer -LHV 043 000 A2-
Edition 10/2010
Product Description
...
Other materials:
Run-Flat Tire PAX
WARNING
Run-flat tires must be replaced after they have gone
flat.
Pay close attention to the installation
instructions. Refer to
→ Chapter „Tir ...
Brake support systems
First read and observe the introductory information
and safety warnings The brake support systems ESC, ABS, BAS,
TCS and EDL only function when the engine is running. They make a considerable contribution
to active driving safety.
Electronic stabilisation programme (ESC)
The ESC helps to ...
Paint Thickness Test -VAS5278
Definition:
Paint Thickness Test -VAS5278-
Product Description
The paint thickness test allows for exact and
interference-free layer thickness measuring of paint coats on
steel, iron or non-f ...
© 2016-2026 Copyright www.vwpolo.net
Two-Part Wash Primer
Filler