Fig. 178 Rear view of the right-hand H4 headlight with plastic covers: ① dipped beam and main beam, ② turn signal and ③ side light
Fig. 179 Rear view of the right-hand H4 headlight with rubber cover: ① dipped beam and main beam, ② turn signal and ③ side light
First read and observe the introductory information and safety warningsThe headlight must be removed in order to change a bulb .
Replacing bulbs in H4 headlights with plastic covers
The actions should only be carried out in the specified order: | |||
---|---|---|---|
① | ② | ③ | |
Dipped beam and main beam headlights | Front turn signal | Side lights | |
1. | Observe and follow the instructions on the checklist . | ||
2. | Open the bonnet . | ||
3. | Release clip ⑥ from catches and pull off plastic cover ⑤. | Pull off plastic cover ⑦. | |
4. | Push retaining clip ④ downwards and unhook at side. | Turn the bulb holder anticlockwise as far as it will go and pull it out to the rear along with the bulb. | Pull the bulb and bulb holder out to the rear. |
Pull the bulb and bulb holder out to the rear. | |||
5. | Remove bulb from bulb holder. If necessary, press the catch on the bulb holder. | ||
6. | Replace the defective bulb with a new bulb of the same type. | ||
7. | Insert bulb holder with bulb and fix the retaining clips ④. | Insert the bulb holder into the headlight and turn it clockwise as far as it will go. | Insert the bulb holder into the headlight. |
8. | Fit the plastic cover ⑤ and push the clip ⑥ towards the opposite side until it engages. | Put the plastic cover ⑦ on and check that it is fitted securely. | |
Then check that it sits correctly. |
Replacing bulbs in H4 headlights with a rubber cover
The actions should only be carried out in the specified order: | |||
---|---|---|---|
① | ② | ③ | |
Dipped beam and main beam headlights | Front turn signal | Side lights | |
1. | Observe and follow the instructions on the checklist . | ||
2. | Open the bonnet . | ||
3. | Pull off rubber cover. | Turn the bulb holder anticlockwise as far as it will go and pull it out to the rear along with the bulb. | |
Push retaining clip ④ downwards and unhook at side. | |||
Pull the bulb and bulb holder out to the rear. | |||
4. | Remove bulb from bulb holder. If necessary, press the catch on the bulb holder. | ||
5. | Replace the defective bulb with a new bulb of the same type. | ||
6. | Insert bulb holder with bulb and fix the retaining clips ④. | Insert the bulb holder into the headlight and turn it clockwise as far as it will go. | |
7. | Put the rubber cover on and check if it is fitted securely. |
The illustrations show the right-hand headlight from the rear. The left-hand headlight is a mirror image of the one shown.
Introduction
This chapter contains information on the following subjects:
→ Ignition lock
→ Starting the engine
→ Stopping the engine
→ Electronic immobilizer
Notes in this chapter concerning the automatic gearbox are applicable
both for the automatic gearbo ...
Securing mounts, roof bars or load carrying system
Fig. 90 Securing points for mounts or
roof bars (both sides) A: for 2-door vehicles without roof railing. B: for 4-door
vehicles without roof railing. C: for vehicles with roof railing
First read and observe the introductory information
and safety warnings
Mounts or roof bars serve as the b ...
Two-Part HS Hardener
Definition:
Two-Part HS Hardener -LHA 009 041 A3-
Two-Part HS Hardener, Short -LHA 021 004 A3-
Two-Part HS Hardener, Extra Short -LHA 009 046 A2-
Two-Part HS Hard ...