Volkswagen Polo Service & Repair Manual: Blender
| Blender was developed for hassle-free two-part clear coat
and top coat touch-up. |
| Applies well to all base surfaces |
| Blends well with the old paint |
| Keep the filler surface as small as possible. |
| Paint filler spot thoroughly with water-based base paint
(overlapping spray applications) |
|
|
|
| Touch-Up System for Two-Part Clear Lacquers |
| Mixing ratio for two-part clear coat: |
| Adjust the two-part clear coat according to technical
application information. Refer to
→ Chapter „Clear Coats“. |
|
|
|
| – |
Paint over the water-based base paint with adjusted clear
coat (overlapping spray applications). |
|
|
|
| – |
Apply pure Blender -LVE 013 100 A2- onto the touch-up area
inside the sanded surface. |
|
|
|
| Touch-Up System for Two-Part Top Coats |
| Mixing ratio for two-part top coat: |
| Adjust the two-part top coat according to technical
application information. Refer to
→ Chapter „Top Coats“. |
|
|
|
| – |
Paint over filler area thoroughly (overlapping spray
applications). |
|
|
|
| – |
Apply pure Blender -LVE 013 100 A2- onto the touch-up area
inside the sanded surface. |
|
|
|
| Polishing the Touch-Up Zones |
| Air dry at +20 °C (68 °F) room temperature: |
| Polish the touch-up areas after they have dried overnight |
|
|
|
| Final drying time with forced drying is a minimum of 5 to 10
minutes. |
|
|
|
| Forced drying is at +60 °C (140 °F) object temperature for
30 minutes. |
| – |
After that, allow the touch-up areas to cool off for an hour
and polish at +20 °C (68 °F) room temperature. |
|
|
|
| Final drying time for IR drying is a minimum of 5 to 10
minutes. |
|
|
|
| IR dry with a short-wave radiator for 10 minutes |
| – |
After that, allow the touch-up areas to cool off for an hour
and polish at +20 °C (68 °F) room temperature. |
 Note
| Polish the touch-up area with fine polishing paste by hand
or with a polishing machine. |
| To finish, treat the surface with high-gloss sealant. |
|
|
|
| Personal Protective Equipment: |
| Note the safety data sheets |
| Wear the personal protective equipment during application |
|
|
|
| Flashpoint: |
+20 °C (68 °F) |
| The guaranteed shelf life of 60 months from date of
manufacture. Use no later than the date indicated on the label
and store in original container at +20 °C (68 °F). |
|
|
|
Definition:
Two-Part HS Performance Clear Coat -LZK 769 K06 A5-
Edition 08/2012
Product Description
...
Other materials:
Introduction
This chapter contains information on the following subjects:
→ Stowage
→ Contents
Observe any country-specific legislation when securing your vehicle in the
event of a breakdown.
Additional information and warnings:
Preparation for working in the engine compartment
...
Securing mounts, roof bars or load carrying system
Fig. 90 Securing points for mounts or
roof bars (both sides) A: for 2-door vehicles without roof railing. B: for 4-door
vehicles without roof railing. C: for vehicles with roof railing
First read and observe the introductory information
and safety warnings
Mounts or roof bars serve as the b ...
Service and disposal of belt tensioners
First read and observe the introductory information
and safety warnings
Seat belts may become damaged during any work on the belt tensioners or while
removing or refitting any vehicle parts in conjunction with any other repair work.
This damage will not always be noticeable. The consequence m ...
© 2016-2026 Copyright www.vwpolo.net
Two-Part HS Performance Clear Coat
Hardener