Volkswagen Polo Service & Repair Manual: Two-Part HS Hardener
Two-Part HS Hardener -LHA 009 041 A3- |
Two-Part HS Hardener, Short -LHA 021 004 A3- |
Two-Part HS Hardener, Extra Short -LHA 009 046 A2- |
Two-Part HS Hardener, Long -LHA 009 047 A3- |
Two-Part HS Hardener, Extra Long -LHA 009 048 A3- |
These are high solid hardeners for several HS fillers and
clear coats. |
It has a high solid content for economical and
environmentally friendly application. |
The choice of five versions means it can adapt well to all
painting conditions and ensure reliable application. |
Possible base components: |
Two-Part HS Vario Filler. Refer to
→ Chapter „Two-Part HS Vario Filler“. |
Two-Part HS Premium Filler. Refer to
→ Chapter „Two-Part HS Premium Filler“. |
Two-Part HS Mixed Filler. Refer to
→ Chapter „Two-Part HS Mixed Filler“. |
Two-Part HS Wet-in-Wet Filler. Refer to
→ Chapter „Two-Part HS Wet-in-Wet Filler“. |
Two-Part HS Clear Coat. Refer to
→ Chapter „Two-Part HS Clear Coat“. |
Two-Part HS Vario Clear Coat. Refer to
→ Chapter „Two-Part HS Vario Clear Coat“. |
1 - |
The Two-Part HS Hardener -LHA 009 041 A3- is suitable for
all complete and partial painting at normal temperatures. |
2 - |
The Two-Part HS Hardener, Short -LHA 021 004 A3- is suitable
for partial painting at low temperatures and low spray booth
ventilation volumes. |
3 - |
The Two-Part HS Hardener, Extra Short -LHA 009 046 A2- is
suitable for spot repairs and partial painting at low
temperatures. |
4 - |
The Two-Part HS Hardener, Long -LHA 009 047 A3- is suitable
for all complete and partial painting at high temperatures. |
5 - |
The Two-Part HS Hardener, Long -LHA 009 048 A3- is suitable
for all complete and partial painting at very high temperatures
and is characterized by its good flow properties. |
|
|
|
– |
Refer to the technical application instructions for the
respective base components |
|
|
|
Hardener selection |
Two-Part HS Hardener -LHA 009 041 A3- |
Two-Part HS Hardener, Short -LHA 021 004 A3- |
Two-Part HS
Hardener, Extra Short -LHA 009 046 A2- |
Partial or complete
painting (large areas) |
+ |
- |
- - |
Partial painting (minor
repairs) |
+ |
+ + |
+ + |
High temperatures above
+25 °C (77 °F) |
+ |
- - |
- - |
Very high temperatures:
+30 °C to +35 °C (86° to 95 °F) |
- |
- - |
- - |
Normal temperature +20 °C
to +25 °C (68° to 77 °F) |
+ + |
- |
- - |
Low temperature +15 °C to
+20 °C (59° to 68 °F) |
- |
+ |
+ + |
Oven drying |
+ + |
+ |
+ |
Air drying |
+ + |
+ + |
+ + |
Hardener selection |
Two-Part HS Hardener, Long -LHA 009 047 A3- |
Two-Part HS
Hardener, Extra Long -LHA 009 048 A3- |
Partial or complete
painting (large areas) |
+ + |
+ + |
Partial painting (minor
repairs) |
+ |
- - |
High temperatures above
+25 °C (77 °F) |
+ |
+ + |
Very high temperatures:
+30 °C to +35 °C (86° to 95 °F) |
+ |
+ + |
Normal temperature +20 °C
to +25 °C (68° to 77 °F) |
+ + |
+ |
Low temperature +15 °C to
+20 °C (59° to 68 °F) |
- |
- - |
Oven drying |
+ + |
+ + |
Air drying |
+ |
+ |
Personal Protective Equipment: |
Note the safety data sheets |
Wear the personal protective equipment during application |
|
|
|
|
Two-Part HS Hardener,
Extra Short -LHA 009 046 A2- |
All other two-part HS
hardeners |
Flashpoint: |
under +21 °C (69.8 °F) |
above +23 °C (73.4 °F) |
All two-part HS hardeners have a guaranteed shelf life of 36
months from date of manufacture. Use no later than the date
indicated on the label and store in original container at +20 °C
(68 °F). |
|
|
|
– |
Protect against moisture. |
|
|
|
– |
Seal the container airtight immediately after removing the
hardener. |
|
|
|
Definition:
Two-Part VHS Hardener -LHA 009 051 A2-/-LVM 009 051 A5-
Two-Part VHS Hardener, Short -LHA 009 050 A2-
...
Other materials:
Tires, Rolling Noises, General Information
Rolling noise perceived by the human ear is caused by
vibrations transmitted from the noise source to the ear via the
air.
Here we are interested in noises created by certain
characteristics of the tires as well as the effects of rolling ...
Wheel, Balancing, Tire and Wheel Radial and Lateral Run-Out, Checking
Before beginning balancing, the following requirements must
be fulfilled.
The tire pressure must be OK.
The tire profile must not be worn on one side. The tire
profile must be at least 4 mm.
...
Removing and installing the headlights
Fig. 176 In the engine
compartment: securing bolts for the right headlight
Fig. 177 Guides for installing the
right headlight
First read and observe the introductory
information and safety warnings
Depending on the vehicle variant, the headlight may have to be removed in
order to replac ...
© 2016-2025 Copyright www.vwpolo.net
